Roper Clothes Dryer 3405639A User Guide

ELECTRIC AND GAS  
DRYERS  
Use & Care Guide  
For questions about features, operation/performance  
parts, accessories or service, call: 1-800-447-6737.  
or visit our website at www.roperappliances.com  
Table of Contents................................................. 2  
3405639A  
 
DRYER SAFETY  
Your safety and the safety of others are very important.  
We have provided many important safety messages in this manual and on your appliance. Always read and obey all  
safety messages.  
This is the safety alert symbol.  
This symbol alerts you to potential hazards that can kill or hurt you and others.  
All safety messages will follow the safety alert symbol and either the word “DANGER” or  
“WARNING.” These words mean:  
You can be killed or seriously injured if you don't  
immediately follow instructions.  
You can be killed or seriously injured if you don't  
follow instructions.  
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you  
what can happen if the instructions are not followed.  
WARNING: For your safety, the information in this manual must be followed to minimize  
the risk of fire or explosion, or to prevent property damage, personal injury, or death.  
Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this  
or any other appliance.  
WHAT TO DO IF YOU SMELL GAS:  
Do not try to light any appliance.  
Do not touch any electrical switch; do not use any phone in your building.  
Clear the room, building, or area of all occupants.  
Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's  
instructions.  
If you cannot reach your gas supplier, call the fire department.  
Installation and service must be performed by a qualified installer, service agency, or  
the gas supplier.  
3
 
IMPORTANT SAFETY INSTRUCTIONS  
WARNING: To reduce the risk of fire, electric shock, or injury to persons when using the dryer, follow basic  
precautions, including the following:  
I
I
Read all instructions before using the dryer.  
I
Do not repair or replace any part of the dryer or  
attempt any servicing unless specifically recom-  
mended in this Use and Care Guide or in published  
user-repair instructions that you understand and have  
the skills to carry out.  
Do not place items exposed to cooking oils in  
your dryer. Items contaminated with cooking oils  
may contribute to a chemical reaction that could  
cause a load to catch fire.  
I
I
Do not use fabric softeners or products to eliminate  
static unless recommended by the manufacturer of  
the fabric softener or product.  
Do not use heat to dry articles containing foam rubber  
or similarly textured rubber-like materials.  
I
Do not dry articles that have been previously  
cleaned in, washed in, soaked in, or spotted with  
gasoline, dry-cleaning solvents, other flammable,  
or explosive substances as they give off vapors  
that could ignite or explode.  
I
I
Do not allow children to play on or in the dryer.  
Close supervision of children is necessary when  
the dryer is used near children.  
I
I
Clean lint screen before or after each load.  
Keep area around the exhaust opening and adjacent  
surrounding areas free from the accumulation of lint,  
dust, and dirt.  
The interior of the dryer and exhaust vent should be  
cleaned periodically by qualified service personnel.  
Before the dryer is removed from service or dis-  
carded, remove the door to the drying compart-  
ment.  
Do not reach into the dryer if the drum is moving.  
Do not install or store the dryer where it will be  
exposed to the weather.  
I
I
I
I
See installation instructions for grounding require-  
ments.  
I
Do not tamper with controls.  
SAVE THESE INSTRUCTIONS  
4
 
PARTS AND FEATURES  
1
4
5
2
3
6
1. Control panel  
Large side-swing door  
Super wide-swing door  
Additional features your dryer may have  
End of Cycle Signal selector  
Drum light  
2. Model and serial number label  
3. Dryer drum  
4. Lint screen  
Small side-swing door  
5. Exhaust grille  
6. Wide-opening door  
Optional purchase  
Drying rack  
Control Panel  
NOTE: The drawings in this book may vary from your dryer. They are designed to show all of the models covered by this book.  
Your dryer may not include all features.  
5
 
3. The exhaust vent can be routed up, down, left, right, or  
straight out the back of the dryer. Space requirements are  
listed in your Installation Instructions.  
CHECKING  
YOUR VENT  
Your dryer must be properly installed and vented to achieve  
maximum drying efficiency and shorten drying times. Use the  
minimum recommended installation clearances (found in your  
Installation Instructions) to avoid blocking the flow of combustion  
and ventilation air. Refer to your Installation Instructions for more  
information.  
4. Use the straightest path possible when routing the exhaust  
vent. Use the fewest number of elbows and turns. Allow room  
when using elbows or making turns. Bend vent gradually to  
avoid kinking.  
Fire Hazard  
Use a heavy metal vent.  
5. Use clamps to seal all joints. Do not use duct tape, screws or  
other fastening devices that extend into the interior of the  
vent to secure vent.  
Do not use a plastic vent.  
Do not use a metal foil vent.  
6. Clean exhaust vent periodically, depending on use, but at  
least every 2 years, or when installing your dryer in a new  
location.  
Failure to follow these instructions can result in  
death or fire.  
I
Disconnect vent from the dryer and clean one section at a  
time until you reach the exhaust hood.  
If the dryer is not properly installed and vented, it will not be  
covered under the warranty.  
NOTE: Service calls caused by improper venting will be paid for  
by the customer, whether it was a paid installation or self-  
installed.  
1. Do not use plastic vent or metal foil vent. Use 4 in. (10.2 cm)  
metal or flexible metal vent. Do not kink or crush flexible  
metal vent. It must be completely extended to allow adequate  
exhaust air to flow. Check vent after installation. Refer to your  
Installation Instructions for proper length requirements of  
vent.  
I
To clean out lint, use the hose attachment on your  
vacuum, or a pole or wire with a feather duster or rag  
attached.  
I
I
Be sure the flapper on the outside end of vent moves  
freely.  
When cleaning is complete, be sure to follow the  
Installation Instructions supplied with your dryer for final  
product check.  
4"  
(10.2 cm)  
2. Use a 4 in. (10.2 cm) exhaust hood. Smaller hoods increase  
drying times.  
2
1
4"  
(10.2 cm)  
4"  
(10.2 cm)  
6
 
to dry most heavyweight and medium weight loads. See  
Drying, Cycle, and Temperature Tips.”  
DRYER USE  
Starting Your Dryer  
3. Select a temperature setting on models with a Temp/Fabric  
selector. The cycle descriptions include temperature setting  
suggestions.  
NOTE: The temperature selector is part of the Cycle Contol  
knob on some models.  
4. Select the End of Cycle Signal, if available. The signal is  
helpful when drying permanent press or synthetics. Promptly  
remove these items from the dryer at the end of the cycle to  
prevent wrinkles.  
Explosion Hazard  
Keep flammable materials and vapors, such as  
gasoline, away from dryer.  
On some models you may have:  
Do not dry anything that has ever had anything  
flammable on it (even after washing).  
I
I
I
An automatic End of Cycle Signal that will sound when  
cycle is completed.  
An End of Cycle Signal that can be adjusted. Turn the  
selector to the desired volume.  
Failure to follow these instructions can result in  
death, explosion, or fire.  
An End of Cycle Signal that is part of the START button.  
Turn the START button to ON or OFF.  
5. Select the desired option. See Additional Features.”  
6. Push the START button.  
Stopping and Restarting  
You can stop your dryer any time during a cycle.  
To stop your dryer  
Open the dryer door or turn the Cycle Control knob to OFF.  
NOTE: The Cycle Control knob should point to an Off area when  
the dryer is not in use.  
Fire Hazard  
To restart your dryer  
1. Close the door.  
No washer can completely remove oil.  
Do not dry anything that has ever had any type of  
oil on it (including cooking oils).  
2. Select a new cycle and temperature (if desired).  
3. Push START.  
Items containing foam, rubber, or plastic must be  
dried on a clothesline or by using an Air Cycle.  
Loading  
Load clothes loosely into the dryer. Do not pack the dryer. Allow  
space for clothes to tumble freely. The following chart shows  
examples of balanced loads that would allow for proper tumbling.  
Failure to follow these instructions can result in  
death or fire.  
Heavy work  
clothes  
3 pair of pants, 4 pair of jeans,  
2 pair of overalls, 3 shirts  
Before using your dryer, wipe the dryer drum with a damp cloth to  
remove dust from storing and shipping.  
1. Load clothes loosely into the dryer and close the door. Do not  
Delicates  
3 camisoles, 1 robe, 4 slips,  
6 undergarments, 2 sets of sleepwear,  
1 childs outfit  
pack the dryer. Allow space for clothes to tumble freely.  
Towels  
10 bath towels, 10 hand towels,  
14 washcloths, 1 bath mat  
Mixed Load  
3 double sheets, 4 pillowcases,  
8 T-shirts, 6 pair of shorts, 2 blouses,  
8 handkerchiefs  
2. Turn the Cycle Control knob to the recommended cycle for  
the type of load being dried. Use the Energy Preferred setting  
7
 
reached. The Cycle Control knob does not move until the load is  
almost dry. After the cool down, the knob automatically turns to  
an Off area and tumbling stops.  
Drying, Cycle and Temperature Tips  
Select the correct cycle and temperature for your load.  
Dry most loads using the Energy Preferred Automatic Setting ( ).  
*
Cool Down tumbles the load without heat during the last few  
minutes of all cycles to make the load easier to handle.  
I
If the load is drier than you like, select a setting closer to  
Less Dry the next time you dry a similar load.  
Drying tips  
I
If the load is not as dry as you like, complete drying using the  
Timed Dry cycle. The next time you dry a similar load, select a  
setting closer to Very Dry.  
I
Follow care label directions when they are available.  
I
If you use fabric softener sheets, use only those labeled  
dryer safe.Follow package instructions.  
NOTE: Drying time with an automatic cycle varies according to  
the type of fabric, size of load, and temperature setting. See  
Drying, Cycle and Temperature Tips.”  
I
Remove the load from the dryer as soon as tumbling stops, to  
reduce wrinkling. This is especially important for permanent  
press, knits, and synthetic fabrics.  
Cycle and temperature tips  
Timed Dry Cycle  
I
I
I
Dry most loads using the Energy Preferred setting, if available  
on your dryer.  
Use the Timed Dry cycle to complete drying if items are still  
damp after the automatic cycle.  
Use a High heat setting for drying heavyweight items such as  
towels and work clothes.  
Timed Dry is also useful for:  
I
Heavyweight and bulky items, such as bedspreads and work  
clothes and large loads that require a long drying time. Set  
the Temperature selector to High heat or to a setting that  
matches the care label directions.  
Use a Medium heat setting for drying medium weight items,  
such as sheets, underwear, permanent press fabrics, and  
some knits.  
I
Lightweight items, such as lingerie, blouses, and knits that  
require a short drying time. Set the Temperature selector at  
Low heat.  
I
I
I
Use a Low heat setting for drying lightweight items such as  
lingerie, blouses, dresses, and some knits.  
Use a no-heat (air) setting for rubber, plastic, or heat-sensitive  
fabrics.  
NOTE: Drying time and temperature will depend on your dryer  
model.  
Line dry bonded or laminated fabrics.  
Max Dry  
NOTE: If you have questions about drying temperatures for  
various loads, refer to the care label directions. If you are unsure  
of the temperature to select for a load, select a lower setting  
rather than a higher setting.  
Select this setting to evenly dry large or heavy items, such as  
thick cotton bath towels or robes. Set the Temperature selector, if  
available, to High heat.  
Damp Dry  
Select this setting to dry items to a damp level or dry items that  
do not require an entire drying cycle. Damp dry items such as  
jeans (to prevent stiffness) or cotton clothes (to make pressing  
easier). Set the Temperature selector, if available, based on the  
fabrics in your load.  
CYCLES  
This manual covers several different models. Your dryer may vary  
from the model shown and may not have all of the cycles and  
features described.  
Wrinkle Free  
Use this setting to remove wrinkles from items, such as clothes  
packed in a suitcase or items wrinkled from being left in the dryer  
too long. Set the Temperature selector, if available, at Low or  
Medium heat, depending on the fabrics in your load.  
Cycle Control knob  
No Heat/Fluff Cycle  
Use the No Heat/Fluff cycle for items that require drying without  
heat, such as rubber, plastic and heat-sensitive fabrics. See the  
chart for examples of items that can be dried using the No Heat/  
Fluff cycle.  
Type of Load  
No Heat/Fluff  
cycle*  
Foam rubber - pillows, padded bras,  
stuffed toys  
20 - 30  
20 - 30  
40 - 50  
10 - 20  
Plastic - shower curtains, tablecloths  
Rubber-backed rugs  
Automatic Cycle  
Olefin, polypropylene, sheer nylon  
Use the automatic cycle to dry most loads. Your dryer uses the  
AUTO SENSE DRY automatic control that senses the moisture in  
the load and shuts off the dryer when the selected dryness is  
*(Minutes). Reset cycle to complete drying, if needed.  
8
 
When using No Heat/Fluff  
This chart shows examples of items that can be rack-dried and  
the suggested cycle, temperature setting, and drying time. Actual  
drying time will depend on the amount of moisture items hold.  
I
I
I
Check to see that coverings are securely stitched.  
Shake and fluff pillows by hand periodically during cycle.  
Dry item completely. Foam rubber pillows are slow to dry.  
Rack Dry  
Cycle  
Temp  
Time*  
Wool Sweaters  
Block to shape and lay flat on  
the rack  
Timed  
Dry  
Low  
60  
Additional Features  
WRINKLE PREVENTfeature  
Stuffed toys or pillows  
Timed  
Dry  
Low  
60  
90  
90  
When you are unable to remove a load of clothes from the dryer  
as soon as it stops, wrinkles can form. The WRINKLE  
PREVENTfeature periodically tumbles, rearranges and fluffs  
the load without heat for up to 45 minutes. During this cycle, the  
dryer stops tumbling and then begins to tumble again. This stop  
and start process is repeated until the end of the cycle. A signal  
will sound periodically when the WRINKLE PREVENTfeature is  
on, if the End of Cycle Signal is selected. The signal and the  
tumbling will end when you open the dryer door, or turn the Cycle  
Control knob to Off.  
Cotton or polyester fiber filled  
Stuffed toys or pillows  
Foam rubber filled  
Air  
None  
None  
(no heat)  
Sneakers or canvas shoes  
Air  
(no heat)  
*(Minutes). Reset cycle to complete drying, if needed.  
I
On some models, the WRINKLE PREVENTfeature is  
automatic and activates at the end of the cycle if you do not  
open the dryer door within a few minutes after the cycle ends.  
DRYER CARE  
I
On some models, you can turn the WRINKLE PREVENT™  
feature On or Off.  
End of Cycle Signal  
Cleaning the Lint Screen  
If the End of Cycle Signal is On, the signal sounds when a cycle is  
complete. If the WRINKLE PREVENTfeature is on, the signal  
sounds every few minutes. The signal stops when you open the door.  
Every load cleaning  
The lint screen is located on the top of the dryer. Clean it before  
each load. A screen blocked by lint can increase drying time.  
To clean  
1. Pull the lint screen towards you. Roll lint off the screen with  
your fingers. Do not rinse or wash screen to remove lint. Wet  
lint is hard to remove.  
Drying Rack  
The drying rack is useful for machine drying items you would not  
necessarily want to tumble dry or that you would normally line dry  
(for example, sweaters or pillows).  
2. Push the lint screen firmly back into place.  
IMPORTANT:  
If your model does not have a drying rack, you may purchase  
one. For ordering information, please refer to the Assistance or  
Servicepage of this manual. You may also contact the dealer  
from whom you purchased your dryer.  
I
Do not run the dryer with the lint screen loose, damaged,  
blocked, or missing. Doing so can cause overheating and  
damage to both the dryer and fabrics.  
To use the drying rack  
I
Some towels made of synthetic fibers and natural fibers  
(polyester and cotton blends) may shed more lint than other  
towels, causing your dryers lint screen to fill up faster. Be  
sure to remove lint from the lint screen before and after drying  
new towels.  
1. Slide rear pegs into the dimples on the back wall of the dryer.  
Lower the front legs to rest on the dryer opening.  
I
If lint falls off the screen into the dryer during removal, check  
the exhaust hood and remove the lint. See Checking Your  
Vent.”  
As needed cleaning  
2. Put the wet items on top of the rack. Leave space between  
Laundry detergent and fabric softener residue can build up on the  
lint screen. This buildup can cause longer drying times for your  
clothes, or cause the dryer to stop before your load is completely  
dry. The screen is probably clogged if lint falls off the screen.  
the items so air can reach all the surfaces. Close the door.  
NOTE: Do not allow items to hang over the edge of the rack.  
3. Select a timed drying cycle and temperature, or an air cycle.  
Items containing foam, rubber, or plastic must be dried on a  
clothesline or by using an air cycle.  
Clean the lint screen with a nylon brush every six months or more  
frequently if it becomes clogged due to a residue buildup.  
4. Push the START button.  
NOTE: The rack must be removed for normal tumbling. Do not  
use the automatic cycle with the drying rack.  
9
 
To wash  
1. Roll lint off screen with your fingers.  
2. Wet both sides of lint screen with hot water.  
Changing the Drum Light  
The dryer light automatically turns on inside the dryer drum when  
you open the door.  
3. Wet a nylon brush with hot water and liquid detergent. Scrub  
lint screen with the brush to remove residue buildup.  
To change the drum light  
1. Unplug dryer or disconnect power.  
2. Open the dryer door. Locate the light bulb cover on the back  
wall of the dryer. Remove the screw located in the lower right  
corner of the cover. Remove the cover.  
3. Turn bulb counterclockwise. Replace the bulb only with a 10-  
watt appliance bulb. Replace the cover and secure with the  
screw.  
4. Rinse screen with hot water.  
5. Thoroughly dry lint screen with a clean towel. Insert lint  
screen back into dryer.  
4. Plug in dryer or reconnect power.  
Cleaning the Dryer Interior  
TROUBLESHOOTING  
First try the solutions suggested here and possibly avoid  
the cost of a service call...  
Clothes are not drying satisfactorily  
I
Check the following:  
Is the lint screen clogged with lint?  
Is the exhaust vent or outside exhaust hood clogged with lint,  
restricting air movement? Run the dryer for 5-10 minutes.  
Hold your hand under the outside exhaust hood to check air  
movement. If you do not feel air movement, clean exhaust  
system of lint or replace exhaust vent with heavy metal or  
flexible metal vent. See your Installation Instructions.  
Explosion Hazard  
Use nonflammable cleaner.  
Failure to do so can result in death, explosion,  
or fire.  
Is the exhaust vent crushed or kinked? Replace with heavy  
metal or flexible metal vent. See your Installation Instructions.  
To clean dryer drum  
1. Make a paste with powdered laundry detergent and very  
Has a fuse blown, or a circuit breaker tripped? Electric dryers  
use 2 household fuses or breakers. The drum may be turning,  
but you may not have heat.  
warm water.  
2. Apply paste to a soft cloth.  
OR  
Has an air dry cycle been selected? Select the right cycle for  
the types of garments being dried. See Drying, Cycle and  
Temperature Tips.”  
Apply a liquid, non-flammable household cleaner to the  
stained area and rub with a soft cloth until all excess dye is  
removed.  
For gas dryers, is the valve open on the supply line?  
3. Wipe drum thoroughly with a damp cloth.  
Are fabric softener sheets blocking the grille? Use only one  
fabric softener sheet, and use it only once.  
4. Tumble a load of clean cloths or towels to dry drum.  
NOTE: Garments which contain unstable dyes, such as denim  
blue jeans or brightly colored cotton items, may discolor the  
dryer interior. These stains are not harmful to your dryer and will  
not stain future loads of clothes. Dry unstable dye items inside-  
out to prevent dye transfer.  
I
Is the dryer located in a room with temperature below  
45ºF (7ºC)?  
Proper operation of dryer cycles requires temperatures above  
45ºF (7ºC).  
I
I
Was a cold rinse water used? Was the load very wet?  
Expect longer drying times with items rinsed in cold water  
and with items that hold moisture (cottons).  
Removing Accumulated Lint  
From Inside the Dryer Cabinet  
Is the load too large and heavy to dry quickly?  
Separate the load to tumble freely.  
Lint should be removed every 2 years, or more often, depending  
on dryer usage. Cleaning should be done by a qualified person.  
Dryer will not run  
From the Exhaust Vent  
Lint should be removed every 2 years, or more often, depending  
on dryer usage.  
I
Check the following:  
Is the power cord plugged in?  
Has a fuse blown, or has a circuit breaker tripped?  
Was a regular fuse used? Use a time-delay fuse.  
Is the dryer door firmly closed?  
Was the START button firmly pressed?  
Is a cycle selected?  
10  
 
I
If the dryer is electric, is it being used for the first time?  
The new electric heating element may have an odor. The odor  
will be gone after the first cycle.  
Unusual sounds  
I
I
Has the dryer had a period of non-use?  
If the dryer hasnt been used for a while, there may be a  
thumping sound during the first few minutes of operation.  
Garment damage  
Is it a gas dryer?  
The gas valve clicking is a normal operating sound.  
I
Check the following:  
Were zippers, snaps, and hooks left open?  
Were strings and sashes tied to prevent tangling?  
Were care label instructions followed?  
Were items damaged before drying?  
Lint on load  
I
I
Is the lint screen clogged?  
Clean lint screen. Check for air movement.  
Is the load properly sorted?  
Sort lint givers (towels, chenille) from lint takers (corduroy,  
synthetics). Also sort by color.  
ASSISTANCE OR SERVICE  
I
I
Is the load too big or too heavy?  
Dry smaller loads so lint can be carried to the lint screen.  
Before calling for assistance or service, please check  
Troubleshooting.It may save you the cost of a service call. If  
you still need help, follow the instructions below.  
Was the load overdried?  
When calling, please know the purchase date and the complete  
model and serial number of your appliance. This information will  
help us to better respond to your request.  
Use correct dryer settings for load type. Overdrying can  
cause lint-attracting static electricity. See Drying, Cycle, and  
Temperature Tips.”  
I
I
Was paper or tissue left in pockets?  
If you need replacement parts  
Is pilling being mistaken for lint?  
Pilling (surface fuzz) is caused by normal wear and  
laundering.  
If you need to order replacement parts, we recommend that you  
only use FSP® replacement parts. These parts will fit right and  
work right, because they are made with the same precision used  
to build every new ROPER® appliance. To locate FSP  
replacement parts in your area, call our Customer Interaction  
Center or your nearest Whirlpool designated service center.  
Stains on load or color change  
I
Was dryer fabric softener properly used?  
Add dryer fabric softener sheets at the beginning of the cycle.  
Fabric softener sheets added to a partially-dried load can  
stain your garments.  
For assistance  
Call the Customer Interaction Center toll free at  
1-800-44-ROPER (1-800-447-6737).  
Our consultants provide assistance with:  
I
I
Were items soiled when placed in the dryer?  
I
I
I
I
I
Features and specifications on our full line of appliances  
Items should be clean before being dried.  
Installation information  
Were items properly sorted?  
Sort light colors from dark colors. Sort colorfast items from  
noncolorfast items.  
Use and maintenance procedures  
Accessory and repair parts sales  
Specialized customer assistance (Spanish speaking, hearing  
impaired, limited vision, etc.)  
Items shrinking  
I
I
Was the dryer overloaded?  
I
Referrals to local dealers, repair parts distributors, and  
service companies.  
Dry smaller loads that will tumble freely.  
Did the load overdry?  
Check the manufacturers care label. Match dryer setting to  
load type. See Drying, Cycle, and Temperature Tips.”  
Whirlpool designated service technicians are trained to fulfill the  
product warranty and provide after-warranty service, anywhere in  
the United States.  
To locate the Whirlpool designated service company in your area,  
you can also look in your telephone directory Yellow Pages.  
Loads are wrinkled  
I
I
Was the load removed from dryer at the end of the cycle?  
For further assistance  
If you need further assistance, you can write with any questions  
or concerns at:  
Was the dryer overloaded?  
Dry smaller loads that can tumble freely.  
Roper Brand Home Appliances  
Customer Interaction Center  
553 Benson Road  
I
Did the load overdry?  
Check the manufacturers care label. Match dryer setting to  
load type. See Drying, Cycle, and Temperature Tips.”  
Benton Harbor, MI 49022-2692  
Please include a daytime phone number in your correspondence.  
Odors  
I
Have you recently been painting, staining or varnishing in  
the area where your dryer is located?  
If so, ventilate the area. When the odors or fumes are gone  
from the area, re-wash and dry the clothing.  
11  
 
ROPER® DRYER WARRANTY  
ONE-YEAR FULL WARRANTY  
For one year from the date of purchase, when this dryer is operated and maintained according to instructions attached to or furnished  
with the product, Whirlpool Corporation will pay for FSP® replacement parts and repair labor to correct defects in materials or  
workmanship. Service must be provided by a Whirlpool designated service company.  
Whirlpool Corporation will not pay for:  
1. Service calls to correct the installation of your dryer, including venting. Heavy 4 in. (10.2 cm) metal exhaust vent must be used. Refer  
to the venting section of this manual and your Installation Instructions.  
2. Service calls to instruct you how to use your dryer, to replace house fuses or correct house wiring or reset circuit breakers, or to  
replace owner accessible light bulbs.  
3. Repairs when your dryer is used in other than normal, single-family household use.  
4. Damage resulting from accident, alteration, misuse, abuse, fire, floods, acts of God, improper installation (including, but not limited  
to, venting with plastic or flexible foil), installation not in accordance with local electrical and plumbing codes, or use of products not  
approved by Whirlpool Corporation.  
5. Replacement parts or repair labor costs for units operated outside the United States.  
6. Pickup and delivery. This product is designed to be repaired in the home.  
7. Repairs to parts or systems resulting from unauthorized modifications made to the appliance.  
WHIRLPOOL CORPORATION SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES.  
Some states do not allow the exclusion or limitation of incidental or consequential damages, so this exclusion or limitation may not  
apply to you. This warranty gives you specific legal rights and you may also have other rights which vary from state to state.  
Outside the 50 United States, this warranty does not apply. Contact your authorized Roper dealer to determine if another  
warranty applies.  
If you need service, first see the Troubleshootingsection of this book. Additional help can be found by checking the Assistance or  
Servicesection or by calling the Customer Interaction Center toll free at 1-800-44-ROPER (1-800-447-6737) from anywhere in the  
U.S.A. or write: Roper Brand Home Appliances, Customer Interaction Center, 553 Benson Road, Benton Harbor, MI 49022-2692. 1/02  
Keep this book and your sales slip together for future  
Dealer name____________________________________________________  
reference. You must provide proof of purchase or installation  
date for in-warranty service.  
Address________________________________________________________  
Phone number__________________________________________________  
Model number __________________________________________________  
Serial number __________________________________________________  
Purchase date __________________________________________________  
Write down the following information about your dryer to better  
help you obtain assistance or service if you ever need it. You will  
need to know your complete model number and serial number.  
You can find this information on the model and serial number  
label, located on your appliance as shown in Parts and  
Features.”  
3405639A  
© 2002 Whirlpool Corporation.  
5/02  
Printed in U.S.A.  
All rights reserved.  
® Registered Trademark/TM Trademark of Whirlpool, U.S.A.  
 

Radio Shack Radio 120 0615 User Guide
RCA CD Player GES050 User Guide
Reebok Fitness Home Gym RBEL59040 User Guide
Renesas Computer Hardware M30100 User Guide
Rheem Water Dispenser 316937A User Guide
Rosewill Network Card N600PCE User Guide
Rosewill Network Card RC 101 User Guide
Samsung Computer Monitor SyncMaste 721B User Guide
Scag Power Equipment Lawn Mower STT52V 25CH LP User Guide
Schumacher Power Supply 00 99 000674 User Guide