49-830.fm Page 1 Thursday, August 19, 1999 10:37 AM
Cat. No. 49-830
OWNER’S MANUAL
RS-3000 Auto Security Alarm System
Please read this entire manual before you begin installation.
49-830.fm Page 3 Thursday, August 19, 1999 10:37 AM
Instant Panic Alarm — calls out in a
female voice to alert others nearby
that you need assistance when you
are in or near your vehicle.
Warning: Your alarm system’s alerts
are painfully loud. Take care during
installation to keep your head away
from the system once you connect
power.
Valet Mode — lets you easily prevent
passive arming when the vehicle is
being serviced, valet parked, or
washed.
FCC INFORMATION
Your alarm system might cause TV or
radio interference even when it is op-
erating properly. To determine wheth-
er your system is causing the
interference, move your vehicle out of
the area. If the interference goes
away, your alarm system was caus-
ing the interference. Try to eliminate
the interference by:
Programmable Options — lets you
customize several of your alarm’s op-
tions.
Accessory Trigger Output — pro-
vides a negative trigger to activate
(but not power) accessory sensors.
Violation Confirmation — beeps
three times or says “I was tampered
with!” when you disarm the system af-
ter the alarm has sounded, to let you
know what happened while you were
away from the vehicle.
• Keeping your system away from
the receiver
• Contacting
your
local
Ra-
dioShack store for help
If you cannot eliminate the interfer-
ence, the FCC requires that you stop
using your alarm system.
Computer-Controlled Fan Sensor
— can tell the difference between
your vehicle’s dome or trunk light and
an electric cooling fan (which can
make other alarms sound a false
alert) without using additional wiring.
Toll-Free Help — if you have any
questions about or problems with
your alarm system, just call:
1-800-598-2527
Your system requires one 9-volt alka-
line battery to maintain operation if
the main power lead is disconnected.
Need Help? Call 1-800-598-2527
3
49-830.fm Page 4 Thursday, August 19, 1999 10:37 AM
CONTENTS
Installing the System ..................................................................................... 5
Supplied Items ........................................................................................... 5
Installation Order ....................................................................................... 6
Connecting the Starter Disable Module ..................................................... 6
Connecting the System to Power .............................................................. 7
Activating the Remote Controls ................................................................. 8
Installing the Backup Battery ..................................................................... 8
Mounting the System ................................................................................. 9
Installing the Status Indicator .................................................................. 10
Using the Alarm System ............................................................................... 11
Arming the Alarm ...................................................................................... 11
Temporarily Reducing the Shock Sensor’s Sensitivity ....................... 11
High Theft Alert .................................................................................. 11
Sounding the Panic Alarm ........................................................................ 11
Alarm Violations ....................................................................................... 12
Disarming the System ............................................................................. 12
Using the Car Finder ............................................................................... 12
Setting the System’s Options .................................................................. 13
Setting the Shock Sensor’s Sensitivity .............................................. 13
Setting the Current Sensor ............................................................... 13
Setting the Valet Mode (Passive Arming/Disarming) ........................ 14
Troubleshooting ........................................................................................... 15
Care and Maintenance ................................................................................. 17
Replacing the Fuse .................................................................................. 18
Replacing a Remote Control’s Battery .................................................... 18
Specifications ............................................................................................... 19
4
Need Help? Call 1-800-598-2527
49-830.fm Page 5 Thursday, August 19, 1999 10:37 AM
INSTALLING THE SYSTEM
SUPPLIED ITEMS
Your alarm system includes the following items:
Two Four-Button Remotes
Main System
Mounting Screws
Starter Disable Relay
Wire Tap-In Connectors
Double-Sided Tape
Status Indicator with Bracket and Harness
Wire Ties
Need Help? Call 1-800-598-2527
5
49-830.fm Page 6 Thursday, August 19, 1999 10:37 AM
INSTALLATION ORDER
CONNECTING THE
STARTER DISABLE
MODULE
You can install your system in just 6
easy steps:
1. Connect the starter disable mod-
ule.
The starter disable module interrupts
power to your vehicle’s starter sole-
noid so the vehicle does not start
when the system is armed. Follow
these steps to connect the module.
2. Connect the system to power.
3. Train the remote controls.
4. Install the backup battery.
5. Mount the system.
1. Using the starter solenoid’s color-
coded wires as a guide, locate
the wire that goes from your vehi-
cle’s ignition (key) switch to the
solenoid. This wire is most easily
found where the wires connect to
the ignition switch near the steer-
ing column.
6. Install the status indicator.
We recommend you get a wiring dia-
gram for your vehicle before you be-
gin, so you can easily find your
vehicle’s starter solenoid wire. Wiring
diagrams are available from your ve-
hicle’s dealer or from the Auto Securi-
ty Helpline at 1-800-598-2527.
2. Connect the negative (usually
black) lead from a 12-volt test
lamp or DC voltmeter to a metal
vehicle body part.
You also need a 12-volt test lamp or
DC voltmeter and a wire-piercing
probe adapter (such as RadioShack
Cat. No. 278-715) to ensure proper
installation.
3. Connect the wire-piercing probe
to the positive lead and press the
pin tip through the solenoid wire’s
insulation and into the wire itself.
4. Start your vehicle. The test light
should light or the meter should
indicate voltage only while the
engine is cranking (not while it
is stopped or running).
If the test fails, repeat Steps 2–4
using a different wire until you
find the correct one.
6
Need Help? Call 1-800-598-2527
49-830.fm Page 7 Thursday, August 19, 1999 10:37 AM
5. Turn off the engine. Then cut the
wire you located in Steps 2–4 at a
point where there are several
inches of wire on each side of the
cut.
8. Route the main system’s orange
wire through an existing hole in
1
the firewall, or drill a /4-inch hole
in the firewall, taking care not to
damage anything on the other
side of the firewall. Then plug the
starter disable module’s orange
wire into the main system’s
orange wire.
Note: After you cut this wire, you
are unable to start your vehicle
until you complete the installa-
tion.
Note: If you drill a hole, use a
rubber grommet to protect the
wire from abrasion.
6. Use one of the supplied yellow
wire tap-ins to connect the starter
disable module’s white wire to the
wire going to the solenoid.
9. Use a wire tie to secure the
starter disable module under the
dashboard.
To Starter
To Ignition
Solenoid
Switch
CONNECTING THE
SYSTEM TO POWER
White
Wire
Red
Wire
Warning: We recommend that you
muffle the alarm’s speaker before you
connect the system to power. The
alarm is extremely loud.
Follow these steps to connect the
system to power.
To the Starter Disable Module
1. Connect the system’s red lead to
your vehicle battery’s positive (+)
terminal.
7. Use the other yellow wire tap-in
to connect the starter disable
module’s red wire to the wire
going to the ignition switch.
2. Connect the system’s black lead
to a metal part of the vehicle’s
body that is not insulated from the
main chassis by a plastic part, or
to the battery’s negative (–) termi-
nal. The system says “Thank
you!”
Need Help? Call 1-800-598-2527
7
49-830.fm Page 8 Thursday, August 19, 1999 10:37 AM
ACTIVATING THE
INSTALLING THE
REMOTE CONTROLS
BACKUP BATTERY
You must train the system to respond
to the supplied remote controls.To ac-
tivate both remote controls, immedi-
A 9-volt battery (not supplied) powers
your alarm if its main power is cut.
Follow these steps to install the bat-
tery.
ARM
ately after applying power, press
TALK
on one of the remotes. The sys-
Note: For the best protection and
longest life, we recommend you use
an alkaline battery, such as Ra-
dioShack Cat. No. 23-553.
tem says “System Armed.” Press
ARM TALK
tem. The system says “System Dis-
armed.”
again to disarm the sys-
If the system loses power and the
backup battery is dead or not in-
stalled, the system stops responding
to both remotes. Simply follow this
procedure again to reactivate them.
Both of the supplied system remotes
share the same remote code, but
your system can learn two remote
codes if you want to add another re-
mote control (Cat. No. 49-845). To
activate a second remote control
code, be sure the system is dis-
1. Slide off the compartment cover.
2. Snap a 9-volt battery onto the
battery contacts.
ARM TALK
armed, then hold down
for
10 seconds. The system says “Thank
You.” Press any button on the new re-
mote to activate it.
3. Place the battery in the compart-
ment.
4. Replace the compartment cover.
A new battery powers the alarm for
about 21 hours with no alert, or 15
minutes of continuous alert. The
alarm’s volume is reduced when it is
operating from the battery.
We recommend you replace the bat-
tery every 6 months, even if it has not
been used to power the system.
8
Need Help? Call 1-800-598-2527
49-830.fm Page 9 Thursday, August 19, 1999 10:37 AM
Once you select a location, follow
these steps to mount the system.
MOUNTING THE
SYSTEM
Select a location for your alarm sys-
tem in the engine compartment. For
the best results, the location should
meet the following conditions.
• All wires should reach their con-
nections without going near mov-
ing or hot engine parts.
Note: If necessary, you can
extend the wires using hook-up
wire and butt connectors. Use at
least 18-gauge wire and an insu-
lated wire connector to extend a
wire.
1. Hold the system against the
selected location and mark the
locations of the three mounting
holes.
• The mounting location should be
solid and have no mechanisms or
moving parts on its other side.
1
2. Drill /8-inch holes at the marked
locations, taking care not to drill
into anything behind the mount-
ing surface.
• For the best remote range, the
mounting location should allow
the system’s yellow antenna wire
to hang straight down. Do not cut
or extend the wire — its length is
optimized for best operation.
3. Secure the system to the surface
using the supplied screws.
Note: For the best shock-sensor
operation use all three screws.
• For the loudest siren, the siren
horn should point down toward
the pavement.
• The alarm should not point
straight up, as moisture could col-
lect in the siren horn and damage
the system.
• To prevent water damage, the
system should not be mounted in
a wheel well, directly behind the
radiator grill, or close to the
ground.
Need Help? Call 1-800-598-2527
9
49-830.fm Page 10 Thursday, August 19, 1999 10:37 AM
bottom of the bracket. Then peel
off the adhesive backing from the
other side of the tape and press
the bracket onto the dash.
INSTALLING THE
STATUS INDICATOR
The status indicator goes inside your
vehicle’s passenger compartment. Ei-
ther drill a mounting hole in a dash
panel or use the supplied mounting
bracket to hold the indicator. Follow
these steps to install the indicator.
If you are mounting the indica-
5
tor in the dash, drill a /16-inch
hole at the desired location.
3. Press the supplied grommet into
the mounting hole from the front
of the surface.
1. Locate an existing wire harness
that goes through your vehicle’s
firewall, and push the indicator
into the passenger compartment
through the existing hole.
Grommet
Indicator
If you cannot find an existing wire
harness, drill
a
1/4-inch hole
through the firewall into the pas-
senger compartment. Then push
the indicator through the hole.
Cautions:
4. Press the indicator into the grom-
met from the back of the surface.
• Before drilling, be sure you can
reach the other side of the
hole.
5. Plug the indicator’s harness into
the matching harness on the sys-
tem.
• Do not drill into any mecha-
nism on the other side of the
firewall.
6. Use the supplied wire tie to
secure the wire out of the way.
• Protect the wire by placing a
rubber grommet (not supplied)
in the hole, and route the wire
through the grommet.
7. If you drilled a hole in the firewall,
use silicon sealant (not supplied)
to waterproof the hole.
2. If you are using the supplied
mounting bracket, use dena-
tured alcohol to clean the mount-
ing surface and let the surface
dry completely. Peel the backing
off of one side of the double-
sided tape and press it onto the
10
Need Help? Call 1-800-598-2527
49-830.fm Page 11 Thursday, August 19, 1999 10:37 AM
USING THE ALARM SYSTEM
press ARM CHIRP to reduce sensitivi-
ty). The alarm says “Thank you.”
ARMING THE ALARM
To arm the alarm in the voice
To completely turn off the shock sen-
sor, press the other ARM button twice
within 2 seconds of arming. The
alarm says “Thank you” each time
you press the button.
press ARM TALK. The alarm
mode,
says “System Armed.”
To arm the system in the chirp
press ARM CHIRP. The alarm
mode,
chirps once.
When you disarm and rearm the sys-
tem, the shock sensor returns to its
previous sensitivity setting.
Notes:
• The status indicator flashes when
the system is armed.
High Theft Alert
• The system ignores current-
sensing violations for 40 sec-
onds after it arms.
If you park your vehicle in a high-
crime area, you can further protect
your vehicle by having the alarm an-
nounce that it is protected every 30
seconds.
• The system ignores shock-sen-
sor violations for 8 seconds after
it arms.
• If the valet mode is turned off, the
system arms 60 seconds after
you turn off your vehicle.
To turn on this feature, press FINDER
within 2 seconds of arming. If you
armed the system in the voice mode,
the system says “System Armed” ev-
ery 30 seconds. If you armed the sys-
tem in the chirp mode, the system
chirps twice every 30 seconds.
Temporarily Reducing the
Shock Sensor’s Sensitivity
If you are parking in a severe weather
situation, near a construction zone, or
near heavy traffic, you can temporari-
ly reduce the system’s shock sensor
sensitivity to help prevent false
alarms. To reduce the sensitivity to
half its normal level, first press ARM
TALK or ARM CHIRP to arm the sys-
tem in the desired mode. Then, within
2 seconds, press the other ARM but-
ton (if you first pressed ARM TALK,
SOUNDING THE PANIC
ALARM
To sound a panic alarm, press and
release PANIC. The alarm screams
“Please help me!” and sounds loud
tones for 30 seconds. Press any but-
ton to stop the panic alarm sooner.
Need Help? Call 1-800-598-2527
11
49-830.fm Page 12 Thursday, August 19, 1999 10:37 AM
ALARM VIOLATIONS
DISARMING THE
SYSTEM
Your alarm senses violations by mon-
itoring your vehicle’s electrical system
(current sensing) and by detecting im-
pacts (shock sensing).
To disarm the system, press either
ARM TALK
ARM CHIRP
. The sys-
or
tem confirms that it is disarmed by
saying “System disarmed” or by
beeping twice.
An alert sounds immediately if the
current sensor detects an electrical
drain such as occurs when a dome or
trunk light turns on.
Notes:
• The status indicator is off when
the system is disarmed.
The first time the alarm senses an im-
pact that exceeds its sensitivity level,
it says “You are too close to the vehi-
cle. Please, move away” (if armed in
the voice mode) or chirps 3 times (if
armed in the chirp mode). If it senses
another impact within 30 seconds, the
system sounds a full alert.
• If the valet mode is turned off, the
system rearms itself after
1
minute if you have not started the
vehicle.
• If the system detected a violation
while you were away, it says “I
was tampered with” or beeps
three times when you disarm it.
Note: If an impact is severe, a single
impact can cause a full alert to sound,
without giving a warning.
USING THE CAR FINDER
When your alarm senses a violation,
it sounds an alert for 30 seconds. If
you armed the system in the voice
mode, it yells “I was tampered with”
and sounds loud tones. If you armed
the system in the chirp mode, the sys-
tem sounds loud tones. To silence
the alert sooner, press any button.
The car finder helps you find your ve-
hicle in a dark or crowded parking lot.
To use the car finder, with the system
FINDER
armed, press
chirps 8 times.
. The alarm
12
Need Help? Call 1-800-598-2527
49-830.fm Page 13 Thursday, August 19, 1999 10:37 AM
Setting the Current Sensor
SETTING THE SYSTEM’S
OPTIONS
If your vehicle has electronic acces-
sories that turn on and off automati-
cally while you are away from the
vehicle, the alarm might sound false
alerts. (The system can detect an
electric engine fan, and does not
sound a false alert when the fan
comes on.)
You can adjust the following options:
• Shock Sensor Sensitivity
• Current Sensor (On/Off)
• Valet Mode (On/Off)
Setting the Shock Sensor’s
Sensitivity
To disable the current sensor so ac-
cessories do not trigger an alert, dis-
arm the system. Then hold down
The shock sensor’s initial setting is
fine for most situations. To test the
shock sensor, strike your vehicle on
the hood directly over the alarm.
PANIC
tem chirps twice.
for about 2 seconds. The sys-
To re-enable the current sensor, with
PAN-
the system disarmed, hold down
If the shock sensor is too sensitive or
not sensitive enough, follow these
steps to set it to a different level.
IC
for about 2 seconds. The system
chirps once.
Notes:
1. With the alarm disarmed, hold
FINDER
“Please adjust sensor now.”
down
until the alarm says
• The current sensor does not
operate for 40 seconds after the
system arms.
2. Within 2 seconds, strike your
vehicle with as much force as you
want the alarm to respond to. The
alarm responds with “Thank you.”
Any shock equal to or greater
than the setting triggers the alert.
• You can also try unplugging or
disconnecting electronic acces-
sories such as radar detectors or
cellular phones when you leave
your vehicle, instead of disabling
the current sensor, to prevent the
false alerts.
Notes:
• If you do not strike your vehicle
within 2 seconds, the alarm is set
to its highest sensitivity. This
could cause frequent false alerts.
• The shock sensor does not oper-
ate for 8 seconds after you arm
the system.
Need Help? Call 1-800-598-2527
13
49-830.fm Page 14 Thursday, August 19, 1999 10:37 AM
Setting the Valet Mode
(Passive Arming/Disarming)
The valet mode lets you leave your
vehicle for service or with a valet and
have it arm 60 seconds after you
not
turn off the engine. The default is for
the valet mode to be on (passive arm-
ing is off).
To have your system automatically
arm 60 seconds after you turn off the
engine, hold down ARM CHIRP for
about 10 seconds. The system says
“System Armed.”
To turn on the valet mode (so the sys-
tem does not passively arm), hold
down ARM CHIRP again for about 10
seconds. The system says “System
Disarmed.”
14
Need Help? Call 1-800-598-2527
49-830.fm Page 15 Thursday, August 19, 1999 10:37 AM
TROUBLESHOOTING
This section describes some problems you might encounter and gives possible
solutions.
Problem
Possible Solution
Frequent false alerts
• Another accessory is triggering the alarm. Try
turning off current sensing to see if this solves the
problem. If it does, try turning it back on, then
removing other accessories, one by one, until
you find which accessory is triggering the false
alert. If possible, turn off that accessory when you
leave your vehicle. Common problem accesso-
ries are cellular phones, radar detectors, and
vehicle self-test systems. If you cannot turn off
the accessory, leave current sensing disabled.
Your alarm can tell the difference between
Note:
the vehicle’s electric fan and other accessories,
so the fan does not trigger a false alert if the fan
turns on while the system is armed.
• Your alarm’s electrical connections are not mak-
ing good contact. Check the connections and, if
necessary, connect the power and ground leads
to the vehicle’s battery terminals.
• The shock sensor is too sensitive. See “Setting
the Shock Sensor’s Sensitivity” on Page 13 to
change the sensor’s setting.
• Loud thunderclaps and heavy machinery can
trigger a false alarm. If you know a thunderstorm
is approaching or that heavy machinery will be
used nearby you can temporarily reduce the
shock sensor’s sensitivity or turn it off entirely.
See “Temporarily Reducing the Shock Sensor’s
Sensitivity” on Page 11.
The alarm is not loud
enough
• The system is operating from its backup battery.
Check all power connections.
• The siren is being muffled by the engine or hood.
Try repositioning the siren so it points to the
pavement.
Need Help? Call 1-800-598-2527
15
49-830.fm Page 16 Thursday, August 19, 1999 10:37 AM
Problem
Possible Solution
Alarm does not operate • Check all power connections.
• Check the system’s fuse. If it has blown, see
“Replacing the Fuse” on Page 18.
• Check the remote control’s battery. See “Replac-
ing a Remote Control’s Battery” on Page 18.
Alarm does not sound
when it should
• The shock sensor is not sensitive enough. See
“Setting the Shock Sensor’s Sensitivity” on
Page 13. If you set the shock sensor to its maxi-
mum sensitivity and the alarm still does not
sound, confirm that you mounted the alarm on a
solid, metal vehicle part (not on the frame or on
rubber or plastic parts). If necessary, reposition
the alarm for better performance.
• If you have a large vehicle, the shock sensor
might not detect impacts on parts of the vehicle
far from the system. Remember that most thieves
break into your vehicle through one of the front
doors or windows. If you set the system sensitive
enough to detect all impacts, you might experi-
ence frequent and annoying false alarms.
• Confirm that you have not accidently disabled
current sensing. See “Setting the Current Sen-
sor” on Page 13.
The remote control’s
range is poor
• The antenna wire is too close to metal. If possi-
ble, position the yellow antenna wire away from
metal.
• The antenna wire has been cut or extended. The
antenna wire is factory tuned for the best perfor-
mance (a longer antenna actually does not work
as well as the short included antenna wire). If the
wire has been cut, take the system to your local
RadioShack store for repair service.
16
Need Help? Call 1-800-598-2527
49-830.fm Page 17 Thursday, August 19, 1999 10:37 AM
CARE AND MAINTENANCE
Your RadioShack RS-3000 Auto Security Alarm System is an example of supe-
rior design and craftsmanship. The following suggestions will help you care for
the alarm so you can enjoy its protection for years.
Keep the remote controls dry. If they get wet, wipe them dry im-
mediately. Liquids can contain minerals that might corrode the
electronic circuits.
Handle the alarm and remotes gently and carefully. Dropping
them can damage circuit boards and cases and might make the
remotes work improperly.
Use and store the remote controls only in normal temperature en-
vironments. Temperature extremes can shorten the life of elec-
tronic devices, damage batteries, and distort or melt plastic parts.
Keep the remote controls away from dust and dirt, which can
cause premature wear of parts.
Do not use harsh chemicals, cleaning solvents, or strong deter-
CLEANER
gents to clean the alarm.
Use only fresh batteries of the recommended size and type in
your alarm and remote controls. Old or weak batteries can leak
chemicals that can damage your system’s internal circuits.
Modifying or tampering with your alarm’s internal components can cause a mal-
function and might invalidate the alarm’s warranty and void your FCC authoriza-
tion to operate it. If your alarm is not operating as it should, take it to your local
RadioShack store for assistance.
Need Help? Call 1-800-598-2527
17
49-830.fm Page 18 Thursday, August 19, 1999 10:37 AM
REPLACING THE FUSE
REPLACING A REMOTE
CONTROL’S BATTERY
Follow these steps to check the sys-
tem’s fuse and replace it if it has
blown. The system uses a 5-amp 11/4
If your remote control’s range is re-
duced or if the indicator does not light
when you press a button, replace its
battery. Each remote control uses a
12-volt remote control battery (Cat.
No. 23-144). Follow these steps to re-
place the battery.
1
× /4-inch fast-acting fuse (Cat. No.
270-1011).
1. Push together the two halves of
the inline fuse holder (on the red
power wire) and twist them to
separate the halves.
2. Inspect the fuse. If the wire is bro-
ken or not there, replace it.
Caution: Use only a fuse of the
same type and rating. Using a dif-
ferent type of fuse or bypassing
the fuse protection can damage
your alarm or your vehicle’s elec-
trical system.
1. Snap apart the remote control’s
case.
3. Put the new fuse in the holder
and push and twist the holder’s
halves together.
Caution: Take care not to lose
any of the remote control’s
pieces.
2. Replace the battery with a new
one.
3. Put all parts back in place and
snap the case halves back
together.
18
Need Help? Call 1-800-598-2527
49-830.fm Page 19 Thursday, August 19, 1999 10:37 AM
SPECIFICATIONS
Siren Sound Level ................................................ More than 120 dB at 1 Meter
Current Drain ........................................................................... 22 mA (Standby)
1 Amp (Siren Sounding)
Power Requirements ................................................................... 9–16 Volts DC
Alarm Weight ....................................................................................... 1 lb, 8 oz
Remote Carrier Frequency ........................................................... 303.875 MHz
RF Output Power ................................................................ 5,580 µV at 1 Meter
Remote Control Power ................................................. 12-Volt Alkaline Battery
Remote Weight ......................................................................................... 1.5 oz
Specifications are typical; individual units might vary. Specifications are subject
to change and improvement without notice.
Need Help? Call 1-800-598-2527
19
49-830.fm Page 20 Thursday, August 19, 1999 10:37 AM
Limited Ninety-Day Warranty
This product is warranted by RadioShack against manufacturing defects in material and workman-
ship under normal use for ninety (90) days from the date of purchase from RadioShack company-
owned stores and authorized RadioShack franchisees and dealers. In the event of a product defect
during the warranty period, take the product and the RadioShack sales receipt as proof of purchase
date to any RadioShack store. RadioShack will, at its option, unless otherwise provided by law:
(a) correct the defect by product repair without charge for parts and labor; (b) replace the product
with one of the same or similar design; or (c) refund the purchase price. All replaced parts and prod-
ucts, and products on which a refund is made, become the property of RadioShack. New or recondi-
tioned parts and products may be used in the performance of warranty service. Repaired or replaced
parts and products are warranted for the remainder of the original warranty period. You will be
charged for repair or replacement of the product made after the expiration of the warranty period.
This warranty does not cover: (a) damage or failure caused by or attributable to acts of God, abuse,
accident, misuse, improper or abnormal usage, failure to follow instructions, improper installation or
maintenance, alteration, lightning or other incidence of excess voltage or current; (b) any repairs
other than those provided by a RadioShack Authorized Service Facility; (c) consumables such as
fuses or batteries; (d) cosmetic damage; (e) transportation, shipping or insurance costs; or (f) costs
of product removal, installation, set-up service adjustment or reinstallation.
EXCEPT AS PROVIDED HEREIN, RadioShack MAKES NO EXPRESS WARRANTIES AND ANY
IMPLIED WARRANTIES, INCLUDING THOSE OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO THE DURATION OF THE WRITTEN
LIMITED WARRANTIES CONTAINED HEREIN. EXCEPT AS PROVIDED HEREIN, RadioShack
SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO CUSTOMER OR ANY OTHER PERSON
OR ENTITY WITH RESPECT TO ANY LIABILITY, LOSS OR DAMAGE CAUSED DIRECTLY OR
INDIRECTLY BY USE OR PERFORMANCE OF THE PRODUCT OR ARISING OUT OF ANY
BREACH OF THIS WARRANTY, INCLUDING, BUT NOT LIMITED TO, ANY DAMAGES RESULT-
ING FROM INCONVENIENCE, LOSS OF TIME, DATA, PROPERTY, REVENUE, OR PROFIT OR
ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, EVEN IF Ra-
dioShack HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
Some states do not allow the limitations on how long an implied warranty lasts or the exclusion of in-
cidental or consequential damages, so the above limitations or exclusions may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights which vary from
state to state.
RadioShack Customer Relations, Dept. W, 100 Throckmorton St., Suite 600, Fort Worth, TX 76102
We Service What We Sell
1/97
RadioShack
A Division of Tandy Corporation
Fort Worth, Texas 76102
2/97
Printed in the USA
|